IJSTR

International Journal of Scientific & Technology Research

Home About Us Scope Editorial Board Blog/Latest News Contact Us
0.2
2019CiteScore
 
10th percentile
Powered by  Scopus
Scopus coverage:
Nov 2018 to May 2020

CALL FOR PAPERS
AUTHORS
DOWNLOADS
CONTACT

IJSTR >> Volume 9 - Issue 4, April 2020 Edition



International Journal of Scientific & Technology Research  
International Journal of Scientific & Technology Research

Website: http://www.ijstr.org

ISSN 2277-8616



Fabrication Of GFRP Composite And To Analyse Its Delamination Factor In Drilling Using Three Different Tool Geometries

[Full Text]

 

AUTHOR(S)

Arun.K, Ramesh Kannan.C and Milon Selvam Dennison

 

KEYWORDS

GFRP; Drill geometry; Delamination; Digital Image Analysis

 

ABSTRACT

The objective of this research work is to fabricate a lightweight, high strength and high stiffness Glass Fibre Reinforced Plastic (GFRP) composite and to perform drilling operation with internal diameter of 8mm on the fabricated GFRP composite plate with three drill bit geometries such as twist drill, trepanning drill and 8 facet drill. The response obtained is the delamination factor with the aid of Digital Image Analysis. The results revealed that drilling with 8 facet drill tool exhibited the optimum condition on the fabricated GFRP composite.

 

REFERENCES

[1]. Piccinno, F., Hischier, R., Saba, A., Mitrano, D., Seeger, S. and Som, C., 2016. Multi-perspective application selection: a method to identify sustainable applications for new materials using the example of cellulose nanofiber reinforced composites. Journal of Cleaner Production, 112, pp.1199-1210.
[2]. Selvam, M.D. and Senthil, P., 2016. Investigation on the effect of turning operation on surface roughness of hardened C45 carbon steel. Australian Journal of Mechanical Engineering, 14(2), pp.131-137.
[3]. Chen, H., Ginzburg, V.V., Yang, J., Yang, Y., Liu, W., Huang, Y., Du, L. and Chen, B., 2016. Thermal conductivity of polymer-based composites: Fundamentals and applications. Progress in Polymer Science, 59, pp.41-85.
[4]. Yan, L., Kasal, B. and Huang, L., 2016. A review of recent research on the use of cellulosic fibres, their fibre fabric reinforced cementitious, geo-polymer and polymer composites in civil engineering. Composites Part B: Engineering, 92, pp.94-132.
[5]. Dennison, M.S., Meji, M.A., Nelson, A.J.R., Balakumar, S. and Prasath, K., 2019. A comparative study on the surface finish achieved during face milling of AISI 1045 steel components using eco-friendly cutting fluids in near dry condition. International Journal of Machining and Machinability of Materials, 21(5-6), pp.337-356.
[6]. Alkbir, M.F.M., Sapuan, S.M., Nuraini, A.A. and Ishak, M.R., 2016. Fibre properties and crashworthiness parameters of natural fibre-reinforced composite structure: A literature review. Composite Structures, 148, pp.59-73.
[7]. Gaugel, S., Sripathy, P., Haeger, A., Meinhard, D., Bernthaler, T., Lissek, F., Kaufeld, M., Knoblauch, V. and Schneider, G., 2016. A comparative study on tool wear and laminate damage in drilling of carbon-fiber reinforced polymers (CFRP). Composite Structures, 155, pp.173-183.
[8]. Geng, D., Liu, Y., Shao, Z., Lu, Z., Cai, J., Li, X., Jiang, X. and Zhang, D., 2019. Delamination formation, evaluation and suppression during drilling of composite laminates: a review. Composite Structures.
[9]. Ismail, S.O., Dhakal, H.N., Popov, I. and Beaugrand, J., 2016. Comprehensive study on machinability of sustainable and conventional fibre reinforced polymer composites. Engineering Science and Technology, an International Journal, 19(4), pp.2043-2052.
[10]. Aamir, M., Tolouei-Rad, M., Giasin, K. and Nosrati, A., 2019. Recent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review. The International Journal of Advanced Manufacturing Technology, 105(5-6), pp.2289-2308.
[11]. Ramesh, M., Palanikumar, K. and Reddy, K.H., 2017. Plant fibre based bio-composites: Sustainable and renewable green materials. Renewable and Sustainable Energy Reviews, 79, pp.558-584.
[12]. Wang, X.M. and Zhang, L.C., 2003. An experimental investigation into the orthogonal cutting of unidirectional fibre reinforced plastics. International journal of machine tools and manufacture, 43(10), pp.1015-1022.
[13]. Mohan, N.S., Ramachandra, A. and Kulkarni, S.M., 2005. Influence of process parameters on cutting force and torque during drilling of glass–fiber polyester reinforced composites. Composite structures, 71(3-4), pp.407-413.
[14]. Zitoune, R. and Collombet, F., 2007. Numerical prediction of the thrust force responsible of delamination during the drilling of the long-fibre composite structures. Composites Part A: Applied Science and Manufacturing, 38(3), pp.858-866.
[15]. Davim, J.P., Rubio, J.C. and Abrao, A.M., 2007. A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Composites Science and Technology, 67(9), pp.1939-1945.
[16]. Dharan, C.K.H. and Won, M.S., 2000. Machining parameters for an intelligent machining system for composite laminates. International Journal of Machine Tools and Manufacture, 40(3), pp.415-426.
[17]. Palanikumar, K., 2011. Experimental investigation and optimisation in drilling of GFRP composites. Measurement, 44(10), pp.2138-2148.
[18]. Raji, M., Abdellaoui, H., Essabir, H., Kakou, C.A., Bouhfid, R. and el kacem Qaiss, A., 2019. Prediction of the cyclic durability of woven-hybrid composites. In Durability and Life Prediction in Biocomposites, Fibre-Reinforced Composites and Hybrid Composites (pp. 27-62). Woodhead Publishing.