IJSTR

International Journal of Scientific & Technology Research

IJSTR@Facebook IJSTR@Twitter IJSTR@Linkedin
Home About Us Scope Editorial Board Blog/Latest News Contact Us
CALL FOR PAPERS
AUTHORS
DOWNLOADS
CONTACT
QR CODE
IJSTR-QR Code

IJSTR >> Volume 5 - Issue 9, September 2016 Edition



International Journal of Scientific & Technology Research  
International Journal of Scientific & Technology Research

Website: http://www.ijstr.org

ISSN 2277-8616



Model Thermoelectric Generator (TEG) Small Modular As Micro Electricity Plant At Indonesia Part 1: Design And Material

[Full Text]

 

AUTHOR(S)

Kisman M. Mahmud, Sri Anastasia Yudistirani, Anwar Ilmar Ramadhan

 

KEYWORDS

Thermoelectric generators, TEG Material, Thermoelectric Cooling, Semiconductor, Micro electric plant

 

ABSTRACT

Thermoelectrically Generator (TEG) can generate electricity from the temperature difference between hot and cold, at the junction thermoelectric module with two different semiconductor materials, there will be a flow of current through the junction so as to produce a voltage. This principle uses the Seebeck effect thermoelectric generator as a base. By using these principles, this study was conducted to determine the potential of the electric energy of the two Peltier modules which would be an alternative source for micro electricity plant using heat from methylated. The focus of this research is to design a model TEG (Thermoelectric Generator) Small Modular to produce the kind of material that is optimum for a TEG on the simulation Computer Aided Design (CAD) with a variety of four different materials that Bi2Te3 (Bismuth Telluride), PbTe-BiTe, CMO-32 -62S Cascade and CMO-32-62S [Calcium Manganese Oxide], to its cold side using the heat sink fan and simulating heat aluminum plate attached to the hot side of the TEG modules with heat source of methylated. Model simulation results on TEG Small Modular micro electrical plant material obtained CMO-32-62S Cascade thermal material that has a value greater than 3 other material.

 

REFERENCES

[1] Farid, Lagiyono, Y. Ivayana, 2011, Thermoelectric Power System Analysis Based on a series circuit with Heat Utilization Remove Machine Toyota 4K mode, Journal of Engineering, Vol. 2 No. 1

[2] F. Keith and A. Priyono, 1986, Heat Transfer, Erlangga, Jakarta

[3] G. Min, and D. M. Roe, 1994, Handbook of Thermoelectrics, Peltier Device As Generator, CRC Press LLC, Florida, p.479

[4] S. O’Halloran, 2012, Power and Efficiency Measurement In A Thermoelectric Generator, AC 2012-3976, University of Portland.

[5] Ryanuargo, S. Anwar, and S. P. Sari, 2013, Thermoelectric Generator Mini Principles of Hot Steam Condensers in Refrigeration Systems, Journal of Rekayasa Elektrika Vol. 10, No. 4, pp. 180-185

[6] N. Putra, R. A. Koestoer, M. Adhitya, A. Roekettino, and B. Trianto, 2009, Thermoelectric Power Plants Potential for Hybrid Vehicles, Makara, Teknologi, Vol. 13, No. 2, pp. 53-58

[7] R. Wirawan, 2012, Analysis Using Heat Pipe On Thermoelectric Generator, Final Project of Undergraduate, Faculty of Engineering, Universitas Indonesia

[8] R. Riksanagara, 2012, Design and Implementation of Thermoelectric Module On Fire Charging System For Customers Ascent, Journal, Telkom University, Bandung.

[9] N. Sulistiyanto, 2014, Thermoelectric Cooling System Modeling at Super Luminance LED Module, Jornal of EECCIS Vol. 8, No. 1, pp. 67-72

[10] Z. Djafara, N. Putra, R.A. Koestoer, 2010, Experimental Study of Development of Thermoelectric Generators As Power Source, Proceeding of the 9th Nasional Seminar of Mechanical Engineering, Palembang